Throwing Taller on the Pottery Wheel: Full Workshop Replay + 7 Key Tips

If getting centered is the first hurdle on the wheel, throwing tall is usually the second. Maybe you want a mug that actually holds a decent cup of coffee, but you keep making ashtrays, in an effort to throw a large vase, your cylinders keep stopping at three inches or flaring out into bowls. Perhaps you sit down with increasingly large amounts of clay, only to barely make any gains in the height department. Don’t worry, I got you!

This is a full workshop replay, about 29 minutes, recorded during one of my live Open Studio sessions. It's not a quick how-to: I throw a cylinder from 1.75 pounds of porcelain and talk through what I'm doing at every step. If you'd rather skim first, here are the tips that make the biggest difference.

1. Practice to failure on purpose

Pick a weight of clay you're comfortable centering. Make three balls of that weight and plan to scrap all three. On each one, try to pull a little taller than the last. On the third, push until it fails. It's like training at the gym: you find your limit by reaching it. You'll learn where the walls get too thin and what the rim does when it's about to go.

2. Center bigger clay in sections

Over about a pound, wedge thoroughly and expect centering to take more effort. If your hands can't wrap the whole lump, center the top, then the bottom, then the whole thing together. If you keep getting a "volcano" when you cone down, start with a rounded top instead of a flat one.

3. Set the floor when you open

The floor won't change much once you start pulling, so make it even and smooth now. I run a rib across the bottom for a clean transition. Then bring the walls slightly inward before your first pull so they're headed up, not out.

4. Make the first pull your power pull

Start at the very bottom and create a small wave of clay with your outside finger, then ride that wave up the pot. Your outside hand does most of the work; your inside finger receives and counterbalances. Ease off as you rise, so you're barely touching at the rim, then compress the lip. A thick, compressed lip keeps a tall pot from flopping. You can thin it later.

5. Keep your fingers level

This is the one I see most: when a pot goes out instead of up, the inside finger is usually riding higher than the outside one. Whichever finger is higher, the wall grows toward it. Keep the pads of your fingers even, or let the outside finger lead by a hair.

6. Put pressure only where the clay is still thick

On the second pull, feel the wall first. The bottom is still thick and needs most of your pressure; the upper wall is nearly finished and needs almost none. Don't keep moving clay that's already done.

7. Anchor your elbow

As the pot gets taller, your elbow tends to wing out, and that instability goes straight into the clay. Keep it tucked against your body, or brace it on your leg.

A few more things from the demo

  • Wet your hands up to the wrist. The extra water drips down for a longer pull.

  • If something goes wrong mid-pull, don't let go. Hold steady and keep moving up.

  • Pulling and shaping are separate moves. Get your height first, then shape.

  • Cut a practice pot in half. It's the fastest way to see where your walls are thick or thin.

Common questions

Why does my clay come off in a "worm" when I pull up? You're moving clay, which is good. Usually you're pressing a little too hard as you start the wave, so the clay peels off into your hand instead of moving up the wall. Ease the pressure just after you start the pull and check that your inside finger isn't riding high.

How much clay should I use to throw taller? Start with a weight you can center confidently. In the video I use 1.75 pounds of porcelain for a cylinder about five to six inches tall. Go up in weight once you can pull that weight consistently.

Why do my pots flare out when I'm trying to go tall? Usually your inside finger is above your outside finger, or the walls were already leaning out after opening. Bring the walls in before your first pull and keep your fingers level.

Keep practicing

Get the free Cylinder Challenge, a simple practice plan for taller, more even cylinders: Free Guides.

New to the wheel? Wheel Throwing for Absolute Beginners, Part 1 walks you through centering, opening, pulling and trimming, one short lesson at a time.

Next
Next

Making Wheel Thrown Mugs: Workshop Highlights