Getting Started on the Wheel

Four steps to throwing your first cylinder on the pottery wheel, plus fixes for the most common beginner problems. I've taught beginners on the wheel for more than 15 years, and these are the steps that help students succeed.

Get the printable guide (free PDF with note pages) →

My best advice

  1. Fast wheel, slow hands.
  2. Be patient with yourself.
  3. Let go of any particular outcome.
  4. Cut your cylinders in half to see what's going on and where to improve.
  5. Keep showing up and you will get better.
  6. If something breaks, it's OK. You can make another.

There's no single right way to throw a pot. As your skills grow, you'll notice each step flows into the next. Find what works for you and keep going.

Before you start

Weigh your clay. Weigh out three 1-pound balls of clay and cover them in plastic. If you haven't learned to wedge yet, use clay fresh from the bag. If one goes wrong, the next is ready. Weighing your clay teaches you what you can make from a given amount. (See How Much Clay Do I Need? for other forms.)

What you need:

  • A wheel, clay, a bucket of water and a sponge
  • Needle tool and wooden tool
  • Straight-sided rib (an old gift card works)
  • Wire cutter and a ware board

Left-handed? These directions are for throwing right-handed with the wheel turning counterclockwise. Reverse the directions and the wheel.

Step 1: Centering

Watch the centering demo →

Centering is the hardest step for most beginners and takes the longest to master. If you're brand new, expect to spend most of your time here. You can move on before you're fully centered, but things may get a little wonky.

  • Slam the clay down. Dry wheel, dry hands, fresh clay. Throw the clay down on the wheel, hard. If it lands a little off, don't lift it. Push it toward the middle.
  • Seal it to the wheel. Run your finger around the base of the clay where it meets the wheel head so it can't come loose.
  • Find your speed. Find your wheel's fastest speed so you know where it tops out, then slow it to about 60 to 75 percent. From now on, rewet your hands every 20 to 30 seconds.
  • Cone up and down. Left hand at 7 o'clock, pinkie side touching the wheel head, angled slightly down and in. Right hand at 2 o'clock. Press your palms toward each other as they move up, easing off as you rise. Cone up and down twice.
  • Mini cone. Left hand at 7 o'clock, right hand on top at 6 o'clock, hands connected. Push in with your left palm until the clay rises, then press it back down from the center toward you.
  • Hug it in. This is where centering really happens. Apply equal pressure to the side and the top, ease in and ease out, and rinse your hands between moves. Aim for a shape slightly wider than it is tall, like a flan.

Tuck your elbows in. If an elbow can rest on a knee, hip or rib cage, let it. You're using your core, not your arms. You're centered when the clay has no wobble under your hands.

Step 2: Opening

Watch the opening demo →

Opening has two parts. Dropping the hole sets how deep the pot is and how thick the bottom is. Opening sets how wide the bottom is.

Drop the hole

  • Feel from the edge toward the center with your pointer finger, other hand connected.
  • At center, press lightly. It should sink in smoothly with no wobble.
  • Keep it wet: shiny means wet, matte means dry.
  • Press down at an angle so you can always see the bottom.
  • Stop 1/4 inch from the wheel head. Check with your needle tool.

Open

  • Hands connected, elbows tucked. Make a soft hook with your right pointer finger.
  • Start at the bottom center and drag toward your belly button without lifting or pressing down.
  • Stop at the width you want.

Step 3: Pulling up

Watch the pulling up demo →

This is where your pot takes shape. The goal is to reach full height in about three pulls.

  • Slow the wheel to about half your centering speed, and slower as the pot grows.
  • Pace each pull by counting down from 10 to 1.
  • Press harder where the clay is thick and lighter where it's thin.
  • Rinse your hands and set the lip after each pull.

The pull. One left-hand finger inside, one right-hand finger outside, hands connected, elbows tucked. If the clay disappeared, your fingers would touch. Start at the bottom. Press from the outside finger; the inside finger receives the pressure. Ease off as you rise. By the top, you're using almost no pressure. Each pull uses less pressure than the one before, mostly aimed at the thick clay near the bottom. Many potters cushion the outside finger with a sponge. Try it both ways.

Set the lip. The lip is the most delicate part of the pot. After every pull, let it glide between your left thumb and pointer finger with your right pointer finger on top. Very little pressure.

Shaping (optional). Belly the pot out from the inside with a sweeping motion, or use a rib on the outside. Less is more: clay that's had a lot of time and water can't take much change.

Step 4: Finishing

Watch the finishing demo →

  • Trim extra clay. Find the extra clay at the base. Hold your wooden tool like a pencil, beveled side toward the pot, and gently carve it away following the pot's outline. Take your time.
  • Take it off the wheel. Put a puddle of water at the base. Press the wire down to the wheel head and pull it through toward you. With dry hands, grab the pot low and slide it onto your ware board.

Common problems

What happens Likely cause Try this
The hole wanders off center Clay wasn't fully centered, or hands weren't braced Re-center; brace the opening hand against the other
Walls twist or tear Wheel too fast, or pulling too quickly Slow the wheel; count 10 to 1 on each pull
Thick bottom, thin top Not enough pressure at the start of the pull Put most of the pressure in the first inch
Rim is wobbly or uneven Lip not set, or an off-center pull Set the lip after every pull; trim the top with a needle tool
Pot collapses Too much water or time Sponge out the water; aim for three pulls

You just threw a cylinder

With practice you'll refine your technique and move on to bowls, mugs and more. Have fun with it.

Keep going